The SP Racing F3 Acro Flight Controller comes packed with other features such as battery monitoring ports for voltage and current, Sonar support for precision low-altitude hold, and a Buzzer port for audible warnings and notifications. The Programmable LED light functions to give you dedicated output for programmable LEDs – great for orientation, racing, and night flying.
No external inverters required (built-in). Supports 1S (4.2V) and 2S (8.4V) lipo, with 2S power flying experience can. It is a 32bit brush flight controller based on F3 EVO firmware. The SP Racing F3 Acro Flight Controller Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers. F3 EVO Brush is based on the popular F3 EVO from SP RACING.
The SP Racing F3 Acro Flight Controller offers full support for OneShot ESCs for easy PID tuning and a sharper response.
Also included with the SP Racing F3 Acro Flight Controller is the developer-friendly debugging port (SWD) and boot mode selection, unbreakable bootloader. The built-in high-capacity black box flight log recorder allows you to optimize your tuning and see the results of your setup without guesswork. Connect your OSD + SmartPort + SBus + GPS + LED Strip + Battery Monitoring + Sonar + 8 motors – all at the same time!ĭon’t let the size fool you, the tiny yet and lightweight SP Racing F3 Acro Flight Controller has a standard 36x36mm form-factor with 30.5mm mounting holes and weighs just 6 grams. The No-Compromise I/O lets you use all the features all the time e.g. Being open-source means that you too can contribute to the system.
The F3 Flight Controller also runs the open-source Cleanflight flight control (FC) software which has an ever-growing community of friendly developers and users. LKML Archive on help / color / mirror / Atom feed PATCH 5.15 000/177 5.15.11-rc1 review 14:32 Greg Kroah-Hartman 14:32 PATCH 5. The SP Racing F3 Acro Flight Controller builds on tried and tested software, processor, and sensor technology to make your aircraft fly like it’s on rails. The SP Racing F3 Acro Flight Controller next-generation STM32 F3 processor with hardware floating point unit for efficient flight calculations and the ever-faster ARM-Cortex M4 core capable of loops speeds 2x faster than other boards. The hardware was designed by the lead developer of Cleanflight to be more capable than the previous-generation STM32F1-based boards after hearing feedback from the Cleanflight users, contributors, and top pilots. Boards availableĬaution : The issues and the pull-requests are strictly limited to submit problems or suggestions related to the software delivered in this repository.įor any other question related to the product, the hardware performance or characteristics, the tools, the environment, you can submit it to the ST Community on the STM32 MCUs related page.The SP Racing F3 Acro Flight Controller gives you all the features you want, whether you’re into FPV racing, acrobatic flying or drone photography. Release noteĭetails about the content of this release are available in the release note here. The URL is available in a readme.txt file inside the module.
9 4 Configuration Mixer QuadX Bord and Sensor RXSERIAL SERIAL Receiver Provider SBUS. In this FW Package, the module Middlewares/ST/STemWin is not directly accessible. This is my wiring diagram for the SP Racing F3 Controller with SBUS, GPS, OSD, and Telemetry when used with betaflight. So i tried to pinch the pins, and got solid blue, then tried again. But the flash failed On verify the firmware session. When i connect the fc for the 1st time, the led will be solid blue, without pinching the boot pins. You can find in each Projects/ Board name directories a set of software projects (Applications/Demonstration/Examples). I tried to flash sp f3 fc using betaflight to 4.0.6 fw. The STM32CubeF3 MCU Package projects are directly running on the STM32F3 series boards. A full set of software projects (basic examples, applications, and demonstrations) for each board provided for this STM32 series.
the seriously pro racing f3 flight controller ( spracingf3) was designed to give. A consistent set of middleware libraries such as RTOS, USB, FatFS, graphics, touch sensing library. the only stm32 chips we have seen used in flight controllers are f1, 3.
The BSP drivers of each evaluation, demonstration or nucleo board provided for this STM32 series.The STM32 HAL-LL drivers, an abstraction layer offering a set of APIs ensuring maximized portability across the STM32 portfolio.